ATmega128A Datasheet
时间: 2009-07-26 来源: Seawin
浏览量:
文件类型：
文件大小：
下载次数: 128-Kbyte self-programming Flash Program Memory, 4-KbyteSRAM, 4-Kbyte EEPROM, 8 Channel 10-bit A/D-converter.JTAG interface for on-chip-debug.Up to 16 MIPS throughput at 16 MHz. 2.7 - 5.5 Volt operation.
KeyParameter:
Flash (Kbytes): 128; EEPROM (Kbytes): 4; SRAM (Bytes): 4096; Max I/O Pins: 53; F.max (MHz): 16; Vcc (V): 2.7-5.5; 10-bit A/D Channels: 8; Analog Comparator: Yes; 16-bit Timers: 2; 8-bit Timer: 2; Brown Out Detector: Yes; Ext Interrupts: 8; Hardware Multiplier: Yes; Interrupts: 34; ISP: Yes; On Chip Oscillator: Yes; PWM Channels: 8; RTC: Yes; Self Program Memory: Yes; SPI: 1; TWI: Yes; UART: 2; Watchdog: Yes;
GreenPackage TQFP 64 MLF (VQFN) 64
ATmega128A Summary (21 pages, revision C, updated 6/09) ATmega128A (385 pages, revision D, updated 7/09) AVR040: EMC Design Considerations(18 pages, revision D, updated 6/06)This Application Note covers the most common EMC problems designers encounter when using Microcontrollers.
AVR042: AVR Hardware Design Considerations(14 pages, revision F, updated 4/08)This Application Note covers the most common problems encountered when switching to a new microcontroller architecture like the AVR.Solutions and considerations for the most common design challenges are covered.
AVR000: Register and Bit-Name Definitions for the AVR Microcontroller(1 pages, revision B, updated 4/98)This Application Note contains files which allow the user to use Register and Bit names from the databook when writing assembly programs.
AVR030: Getting Started with IAR Embedded Workbench for Atmel AVR(10 pages, revision D, updated 10/04)The purpose of this application note is to guide new users through the initial settings of IAR Embedded Workbench, and compile a simple C-program.
AVR031: Getting Started with ImageCraft C for AVR(8 pages, revision B, updated 5/02)The purpose of this Application Note is to guide new users through the initial settings of the ImageCraft IDE and compile a simple C program.
AVR032: Linker Command Files for the IAR ICCA90 Compiler(11 pages, revision B, updated 5/02)This Application Note describes how to make a linker command file for use with the IAR ICCA90 C-compiler for the AVR Microcontroller.
Debug Tool: AVR JTAGICE mkII
Design Software: Atmel QTouch Library2.0
AVR Studio 4
Mature AVR Studio 3.5
Emulator: Mature ATICE50
Mature AVR JTAG ICE
In-System Programming: AVR ISP In-System Programmer
AVRISP mkII In-System Programmer
Starter Kit: ATSTK500
ATSTK501
ATSTK600
ATSTK600-TQFP64
Mature AVR Embedded Internet
Software Files: Atmel QTouch Library 2.0
AVR BSDL filesZip archive with BSDL files for Atmel AVR devices.
AVR IBIS - Mega filesZip archive with IBIS files for Atmel AVR Mega devices.
AVRSVFAVRsvf is a commandline software that is used to generate Serial Vector Format (SVF) files with complete programming algorithms and content for all Atmel AVR devices with a JTAG interface. SVF files are used as input to most common JTAG programmers or ATE testers.
8-bit Microcontroller Drives Battery-powered Thermostat(Article, 2 pages, updated 1/04) Algorithm Builder for AVR(Article, 2 pages, updated 1/04) Atmel AVR-based Constant Current Supply(Article, 4 pages, updated 1/04) AVR and AVR32 - Quick Reference Guide(Overview, 68 pages, revision I, updated 5/09)Introduction of the product range of AVR and AVR32 microcontrollers and application processors:
Device family description
Key features
Device selection guides
Application oriented device families
Tools offer
AVR Instruction Set(User Guide, 155 pages, revision H, updated 7/09) Construct an ATA Hard Drive Controller(Article, 5 pages, updated 1/04) Heterogeneous Device Networking(Article, 2 pages, updated 1/04) High-level Tool Targeted for AVR Controllers(Article, 2 pages, updated 1/04)
文章评论
共有 位滨凯科技客人发表了评论 查看完 整内容